内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Modeling the effects of green alternative on heat island mitigation of a meso level town,West Bengal,India

Urban heat island (UHI) is emerged as a ubiquitous phenomenon that affects the outdoor thermal comfort. Hence urban microclimatic studies using numeric simulation software to find out adaption strategies are attracting the great attention of researchers and policymaker. Number of scientists carried out their research on this topic using different tools and technique whereas ENVI-met model is the most widely used simulation tools. The present study intended to examine the implication of green infrastructure of the town on enhanced microclimatic condition and to evaluate the best suitable mitigation strategy modelling cool city with ENVI-met software (V4). Five greening condition such as existing UHI condition (C1), 100% greening of roof (C2), 100% greening of roof and walls (C3), 50% greening of roof and walls (C4) and: Plantation at suitable area with 50% greening of roof and walls (C5) have been taken into consideration for the microclimate simulation for all three selected sites. Among these five conditions, C3 for the open mid-rise and compact low-rise, C5 for the open low-rise are identified as one of the most suitable strategies which can reduce the air temperature of peak hours by 2.6 °C, 1.33 °C and 1.87 °C respectively. These models are validated by simple linear regression between simulated and existing air temperature in case of existing UHI condition (C1) and in all the cases coefficient of determination value is high such as for open mid-rise, compact low-rise and open low-rise, it is 0.92, 0.92 and 0.75 respectively. Therefore it can be concluded that the application of those strategies can improve the urban thermal environment as well as the outdoor thermal comfort of English bazaar Town and its surroundings.     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

面向快速响应产品的星上目标定位及识别方法

针对遥感卫星星上目标的定位及识别，本文面向快速响应应用需求，首先对星上目标定位及识别工作模式进行研究，总结出狭义和广义两种模式，其次重点对像方-物方坐标双向定位算法进行梳理，并针对典型地物目标星上自动识别算法提出研究思路，最后给出算法的应用方法流程。本文研究为快速响应产品星上智能处理提供方法参考。     

Mapping mean lake surface from satellite altimetry and GPS kinematic surveys

Lake water height is a key variable in water cycle and climate change studies, which is achievable using satellite altimetry constellation. A method based on data processing of altimetry from several satellites has been developed to interpolate mean lake surface (MLS) over a set of 22 big lakes distributed on the Earth. It has been applied on nadir radar altimeters in Low Resolution Mode (LRM: Jason-3, Saral/AltiKa, CryoSat-2) in Synthetic Aperture Radar (SAR) mode (Sentinel-3A), and in SAR interferometric (SARin) mode (CryoSat-2), and on laser altimetry (ICESat). Validation of the method has been performed using a set of kinematic GPS height profiles from 18 field campaigns over the lake Issykkul, by comparison of altimetry’s height at crossover points for the other lakes and using the laser altimetry on ICESat-2 mission. The precision reached ranges from 3 to 7 cm RMS (Root Mean Square) depending on the lakes. Currently, lake water level inferred from satellite altimetry is provided with respect to an ellipsoid. Ellipsoidal heights are converted into orthométric heights using geoid models interpolated along the satellite tracks. These global geoid models were inferred from geodetic satellite missions coupled with absolute and regional anomaly gravity data sets spread over the Earth. However, the spatial resolution of the current geoid models does not allow capturing short wavelength undulations that may reach decimeters in mountaineering regions or for rift lakes (Baikal, Issykkul, Malawi, Tanganika). We interpolate in this work the geoid height anomalies with three recent geoid models, the EGM2008, XGM2016 and EIGEN-6C4d, and compare them with the Mean Surface of 22 lakes calculated using satellite altimetry. Assuming that MLS mimics the local undulations of the geoid, our study shows that over a large set of lakes (in East Africa, Andean mountain and Central Asia), short wavelength undulations of the geoid in poorly sampled areas can be derived using satellite altimetry. The models used in this study present very similar geographical patterns when compared to MLS. The precision of the models largely depends on the location of the lakes and is about 18 cm, in average over the Earth. MLS can serve as a validation dataset for any future geoid model. It will also be useful for validation of the future mission SWOT (Surface Water and Ocean Topography) which will measure and map water heights over the lakes with a high horizontal resolution of 250 by 250 m.     

Substitution of satellite-based land surface temperature defective data using GSP method

Land surface temperature (LST) as an important environmental variable provides valuable information for earth environmental system modelling. Currently, LST is obtained through satellite thermal sensors at various spatial and temporal resolutions. Although spatially continuous satellite-based LST measurements are intended to overcome the shortcomings of sparse ground-based LST measurements, LST images often contain anomalous values due to the existence of clouds or sensor malfunctioning. The problem becomes more serious where the users deal with high spatial resolution characterized by low temporal resolution. This study examines the capability of a newly developed graph signal processing (GSP) method using two-dimensional single-date thermal data. For this purpose, four Landsat/TIRS datasets are analyzed. The data of five elliptical regions on thermal images are eliminated and then reconstructed through the GSP method and using the LST values of the enclosing rectangles containing the ellipsoids. The results indicate that the temperature variation determined by the GSP method generally conforms to the original image LST values. According to a correlation test conducted on the original image LST and those obtained through the GSP method, the values vary from 58% to 95%, which is an above-the-average rate (RMSE from 0.69 to 2.27). The statistical analysis of the original image LST in both the elliptical regions and the enclosing rectangles containing the ellipsoids indicates that an increase in the variance of LST data causes an increased error in the calculation of temperature by the GSP method, and vice versa. The results of the analysis of variance (ANOVA) and Duncan test indicated that an increase in the number of the non-zero spectral bins would result in increased RMSE values for all the dates and the regions. Moreover, the model errors were significant at the 0.05 level across all the image date and five elliptical study regions. Based on the results, the use of this method is recommended for the reconstruction of LST missing values, where dissimilarity of atmospheric conditions limits the use of other methods that depend on the time series data of various dates and a great deal of data calculation.     

一种针对局部结构的有限元模型修正方法

针对实际结构有限元模型（FEM）的建模误差通常仅存在于局部区域，提出了一种对局部结构单独进行模型修正的方法。首先，根据频响函数（FRF）解耦理论得到由残余结构频响函数与包含待修正参数的局部结构动刚度所重构的整体结构频响函数的拟合值，然后通过迭代优化使其与测量值的残差最小化，从而得到参数的极大似然估计。在此基础上，将残差关于参数的灵敏度以局部结构动力学矩阵表示，建立了模型修正的基本方程，利用整体结构的测试数据即可直接对分离出来的局部结构进行模型修正。最后，对喷气式飞机和三角机翼飞机分别进行了数值模拟和实验研究，验证了所提方法的可行性和有效性。结果表明，所提方法可以成功地用于仅局部区域含有建模误差的实际结构有限元模型的修正，修正后的有限元模型的动态特性与实际结构有较好的一致性。     

AP聚类改进免疫算法用于航空发动机故障诊断

在免疫算法训练过程中引入近邻传播(AP)聚类与熵权法,对训练样本进行聚类与权值计算,将权值引入免疫算法中样本选择阈值的计算,以解决训练过程采用固定选择阈值所造成的检测器在部分区域过拟合,部分区域欠拟合的问题。结果表明:改进的免疫算法用于典型非线性函数的寻优时,迭代性能均优于传统免疫算法,并在大部分情况下优于粒子群算法与量子遗传算法,在进行某型发动机故障诊断的实例实验时,改进后的算法的诊断准确率达到98.06%,高于传统免疫算法的92.60%。